Op voorraad Populair product
HC-HS 2-D7-EBUS
HC-HS 2-D7-EBUS 1586264 PHOENIX CONTACT Contact insert
$35.46
USD
326 op voorraad
Belangrijkste specificaties
:
Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque.
Type:
D7
Tests:
DIN VDE 0627/86
Breedte:
21 mm
Leveranciersinformatie
Producten: 0
Wordt doorgaans binnen 2-3 werkdagen verzonden.
Kwaliteit gegarandeerd
Snelle verzending
Technische ondersteuning
Technische specificaties
| Parameter | Waarde |
|---|---|
| Note regarding axial connection technology:Only for stranded wires. The specified conductor cross sections refer to the geometric cross section of the cable used.Cables with a geometric cross section which deviates significantly from the nominal cable cross section must be checked before use.The axial connection technology connection space is designed for fine strand cables according to VDE 0295 Class 5. Deviating cable structures (e.g., Class 6 cables) must be checked before use.Assembly instructionsBefore assembly, ensure that the tapered screw is fully loosened (chamber is open). Cables must not be twisted. The wires must be pushed into the contact chamber as far as they will go (until the insulation touches the contact). Hold the wires in position and tighten using an Allen key. The used wire end must be cut off before reconnection. The terminal screw must only be retightened once to prevent the litz wires from breaking. To prevent damage to the contact, the wire/cable must be mechanically held at an appropriate distance from the connection point (e.g., when used in a plate cut out). For notes on correct execution, see DIN VDE 0100-520:2003-06. Unused connections must be tightened with maximum torque. | |
| Type | D7 |
| Tests | DIN VDE 0627/86 |
| Breedte | 21 mm |
| Hoogte | 34.8 mm |
| Lengte | 21 mm |
| Serie | HC-HS |
| Algemeen | for HC-D7 housing, axial connection 2.0 mm, Allen key |
| Sollicitatie | Power |
| Producttype | Contact insert with a fixed no. of positions |
| Montage-instructies | To ensure correct use, installation in housing with IP54 protection or better is required |
| Nominale huidige waarde | 40 A |
| Artikelrevisie | 04 |
| Contactdiameter | 4 mm |
| Contactmateriaal | Copper alloy |
| Zeshoekige dop | SW2,0 |
| Contactnummering | 1 - 2 |
| Aanhaalmoment | 0.5 Nm ... 0.8 Nm (Mounting screws for mounting in the HEAVYCON housing) |
| Verbindingsprofiel | 2+PE |
| Mate van vervuiling | 3 |
| Maattekening | |
| Aantal posities | 2 |
| Nominale overspanningsspanning | 6 kV |
| Overspanningscategorie | III |
| Verbindingstechnologie | Axial screw connection |
| Contactmateriaaltype | turned |
| Aantal stroomcontacten | 2 |
| Nominale spanning (III/3) | 400 V |
| Dwarsdoorsnede van een geleider | 4 mm² ... 10 mm² (The cross section specification refers to the geometric cross section of the cable used) |
| Contactmateriaal van de drager | PC |
| Contactoppervlakmateriaal | Ag |
| Inbreng-/onttrekkingscycli | ≥ 500 |
| Aansluitdoorsnede AWG | 10 ... 8 |
| Omgevingstemperatuur (bedrijfstemperatuur) | -40 °C ... 125 °C (including heating up of contacts) |
| Aansluiting conform standaard | IEC / EN |
| Bouw- en testvoorschriften | DIN VDE 0627/86 |
| Brandbaarheidsclassificatie volgens UL 94 | V0 |
| Strippen van de individuele draad | 8 mm +1 mm |
Productbeschrijving
Contact insert, number of poles: 2+PE, size: D7, power contacts: 2, Female, Axial screw connection, 400 V, 40 A, 4 mm² ... 10 mm², Application: Power
Belangrijkste kenmerken
- Industriële kwaliteit
- RoHS-conform
- CE-gecertificeerd
- 1 jaar garantie
Productdocumenten
Gegevensblad
Technische specificaties en prestatiegegevens
Gebruikershandleiding
Installatie- en bedieningshandleiding
